View M6021-01000M_280873.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

FULL SIZE D.I.L.
VOLTAGE CONTROLLED OSCILLATORS HCMOS Logic, -40 to +85C
M6001 thru M6007 L6001 thru L6007 M6021 thru M6023 L6021 thru L6023
HALF SIZE D.I.L.
H6001 thru H6007 H6021 thru H6023
Thru-Hole / Gull Wing, 5V
1 MHz to 125 MHz
Extended Temp Thru-Hole VCXOs, 5V
Industrial temperature (-40C to 85C) thru-hole 5V VCXOs are available in a variety of off-theshelf models. Versions in full size (M) and half size (H) cans are offered as standard designs. These models are recommended for new equipment in exacting environments that operate at 5 volt. Five volt operation permits extreme combinations of pull, control voltage and center frequency deviation, enabling the VCXO to accommodate a wide variety of filtering and driving circuitry. Standard VCXOs are hermetically sealed in full size (M) or half size (H), DIL packages. The many standard designs described here have center frequency stability of 50 ppm, and frequency capture range to 175 ppm. These oscillators have excellent long-term reliability, loading characteristics, and superior startup performance. All VCXOs are tested and guaranteed over the full operating temperature.
These 5V VCXOs generate an HCMOS frequency output which is controlled by an input voltage. The end-point frequency/voltage parameters are defined, as is the center frequency.
CAPTURE RANGE The Frequency-Capture range is equal to the (Center-Frequency the Frequency Deviation), because every MF VCXO is ATE-tested to meet the Frequency-Deviation over the temperature range.Frequency Capture specification includes all effects of temperature and supply voltage. It is not necessary to make additional capture allowances. FEATURES * Frequency from 1 MHz to 125 MHz * Capture-range is fully defined, under all conditions * Start-up time less than 5 ms. * Low profile package available above 60 MHz * Typical jitter is less than 15 ps RMS * Choice of thru-hole or gull wing CONNECTIONS Full Size Pin 1. Pin 7. Pin 8. Pin 14. Half Size Pin 1. Pin 4. Pin 5. Pin 8.
Control Voltage, VC Ground & Case Output +5 Volts, VDD
DOT DENOTES PIN 1 DOT DENOTES PIN 1 DOT DENOTES PIN 1
.52 MAX SQUARE .200 MAX .215 MAX .018 .001 .060 TYP .300 .005 .400 .600 .005 Pin 1 .100 .005 Pin 7 .300 . 005 .150 Pin 14 Pin 8 .250 MAX .500 .005 8 5 .008/025 .15 MIN .018 .300 Pin 1 1 4 .300 Pin 14 .2 MAX .160 .2 MAX .018 .001 .600 .005 Pin 7 .520 .005 .300 . 005 Pin 8 GLASS INSULATORS (4) on .48 x .18 ctrs. 1 8
.800 .005
DOT DENOTES PIN 1
.800 .005
.52 MAX SQUARE .200 MAX .270 MAX .018 .300 +.004 4 5 .300 +.004 .200 MAX .070
GLASS INSULATORS (4) on .48 x .18 ctrs.
Glass Insulators (4)
"M" Package - "L" Package is same as "M" but seated height is 0.190
"H" Package
"M" Package with Gull Wing
"H" Package with Gull Wing
ELECTRONICS
10 Commerce Drive, New Rochelle, NY10801 * 914-576-6570 * Fax: 914-576-6204 * http://www.mfelectronics.com * email:mfsales@mfelec.com 89
FULL SIZE D.I.L.
VOLTAGE CONTROLLED OSCILLATORS HCMOS Logic, -40 to +85C Thru-Hole /Gull Wing, 5V
1 MHz to 125 MHz
M6001 thru M6007 L6001 thru L6007 M6021 thru M6023 L6021 thru L6023
HALF SIZE D.I.L.
H6001 thru H6007 H6021 thru H6023
Center Frequency is Between Two Voltages with 50 ppm stability
Control Voltage (Volts) 0.3 to 10.0 0.3 to 4.0 0.3 to 10.0 0.3 to 4.0 1.0 to 4.0 0 to 5.0 0.5 to 4.5 Frequency Deviation (ppm) 175 min 75 min 175 to 300 125 min 75 to 300 150 min 125 to 250 Guaranteed Control Center Capture Voltage Frequency Range at Center Stability (ppm) Frequency (ppm) 175 75 175 125 75 150 125 2.5 to 5.0 1.3 to 2.3 2.5 to 5.0 1.3 to 2.3 1.8 to 3.0 -- 1.8 to 3.0
SPECIFICATIONS Temperature Operating Storage
-40 to +85C -55 to +125C
MODEL 6001 6002 6003 6004 6005 6006 6007
Frequency Stability VC = 2.5V
50 ppm, max. MIN. 4.5 TYP 5.0 30 MAX 5.5 45 UNITS volts ma
40, typ 50, max
Input Voltage Input Current Output Levels (HCMOS) "0" Level, sinking 16 ma. "1" Level, sourcing 10 ma. Rise and Fall Times, HCMOS From 0.4 to (VDD-.4) V (Above 35 MHz) Symmetry At VDD / 2 Input Impedance, Pin 5., Control Voltage Control Voltage Bandwidth
Center Frequency is at 2.5V with 50 ppm stability
Control Voltage (Volts) 0.5 to 4.5 0.5 to 4.5 0.5 to 4.5 Frequency Deviation (ppm) 75 to 150 100 to 200 150 to 300 Guaranteed Control Center Capture Voltage Frequency Range at Center Stability (ppm) Frequency (ppm) 75 100 150 2.5 2.5 2.5 30, typ 50, max
0.4 VDD -.4
volts volts
MODEL 6021 6022 6023
2.5
4 2
ns ns
.
45/55
percent
DESCRIPTIONS M6001, H6001, L6001 M6002, H6002, L6002 M6003, H6003, L6003 M6004, H6004, L6004 M6005, H6005, L6005 M6006, H6006, L6006 M6007, H6007, L6007 M6021, H6021, L6021 M6022, H6022, L6022 M6023, H6023, L6023
175 ppm, min. deviation when using 0.3 to 10V control-voltage 75 ppm, min. deviation when using 0.3 to 4.0V control-voltage 175 ppm to 300 ppm deviation when using 0.3 to 10V control-voltage 125 ppm deviation when using 0.3 to 4.0V control-voltage 75 ppm to 300 ppm deviation when using 1.0 to 4.0 control-voltage, for use where the control voltage is 1 volt off both rails 150 ppm, min. deviation when using 0 to 5.0 control-voltage 125 ppm to 250 ppm deviation when using 0.5 to 4.5 control-voltage 75 ppm capture when using 0.5 to 4.5V control-voltage and 2.5V center with 50 ppm stability 100 ppm capture when using 0.5 to 4.5V control-voltage and 2.5V center with 50 ppm stability 150 ppm capture when using 0.5 to 4.5V control-voltage and 2.5V center with 50 ppm stability
15 15
1000 150
Kohms KHz
ENVIRONMENTAL SPECIFICATIONS Temperature Cycle - Not to exceed 5 ppm change when exposed to 2 hours maximum at each temperature from 0 to 120C, with 25C reference Shock - 1000 G's, 0.35 ms, 1/2 sine wave, 3 shocks in each plane Vibration - 10-2000 Hz of .06" d.a. or 20 G's, whichever is less Humidity - Resistant to 85 R.H. at 85C
PIN 1. CONTROL VOLTAGE VDD +3.3V Power Supply GND Half Size connections shown in ( ) To adapt Fet probe to receptacle use Tektronix Part #103-0164-00 To connect output to scope use use Tektronix Part #131-0258-00 (receptacle) MA
1 (1) 14 (8)
FET PROBE 350 MHz SCOPE LOAD
Y-OUTPUT
7 (4)
8 (5)
COUNTER
FREQUENCY STABILITY Frequency stability vs. Temperature is typically beter than 40 ppm for -40 to +85C. Since the deviation of each oscillator is tested and guaranteed over the whole operating temperature range, it is not necessary to make additional capture allowances. All oscillators will capture frequencies with the full minimum values of the deviation under all conditions. QUALITY Each VCXO is computer-tested at three temperatures to guarantee full compliance to the specification.
ALL OSCILLATORS HAVE INTERNAL BYPASS CAPACITORS
TEST CIRCUIT
ELECTRONICS
10 Commerce Drive, New Rochelle, NY10801 * 914-576-6570 * Fax: 914-576-6204 * http://www.mfelectronics.com * email:mfsales@mfelec.com 90
FULL SIZE D.I.L.
VOLTAGE CONTROLLED OSCILLATORS HCMOS Logic, -40 to +85C Thru-Hole /Gull Wing, 5V
1 MHz to 125 MHz
M6001 thru M6007 L6001 thru L6007 M6021 thru M6023 L6021 thru L6023
HALF SIZE D.I.L.
H6001 thru H6007 H6021 thru H6023
MECHANICAL SPECIFICATIONS Gross Leak - Each unit checked in 125C flurocarbon Fine Leak - Mass spectrometer leak rate less than 2 X 10-8 atmos, cc/sec of helium Pins - Kovar, nickel plated with 60/40 solder coat Bend Test - Will withstand two bends of 90 from reference Header - Steel, with nickel platel Case - Stainless steel, type 304 Marking - Printing is black epoxy ink Resistance to Solvents - MIL STD 202, Method 215 AGING 3 ppm, first year, typ. 1 ppm per year thereafter, typ.
Fig. 1 M6022-16.384M, with 50 pf load
M6022 -16.384M, TYPICAL
200 150 250 200 150 4.5 Volts 100 50 0 0 -50 -50 -100 -150 -200 -250 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 Temp -40C Temp 0C Temp 25C Temp 85C -100 0.5 Volts -150 -200 0 Volts -250 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 0 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 10 20 30 40 2.5 Volts 50 60 5.0 Volts 80 70 VDD = 4.5V VDD = 5.0V VDD = 5.5V
Frequency Deviation, ppm
100 50
Control Voltage, Vc
Temperature, C
Temperature, C
Fig. 2 Frequency vs. Control Voltage
Fig. 3 Frequency vs. Temperature
Fig. 4 Frequency vs. Temperature @ 2.5V Control Voltage
HOW TO ORDER
For Part Number, put package type before model number, and add frequency in MHz, for example:
M 6 0 0 1- 1 2 . 3 5 2 M G
"M" is full size DIL "H" is half size DIL "L" is low height, full size DIL
"6001" is model type
"12.352 M" frequency in MHz
Add "G" for gullwing
ELECTRONICS
10 Commerce Drive, New Rochelle, NY10801 * 914-576-6570 * Fax: 914-576-6204 * http://www.mfelectronics.com * email:mfsales@mfelec.com 91

▲Up To Search▲

Price & Availability of M6021-01000M

	To Download M6021-01000M Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .